November 2013 - Only Deco

Hot

Monday, 18 November 2013

rolled paper ornaments (tutorial)

12:08:00 0


1. Cut construction paper lengthwise (9″ long) in the following widths, in alternating colors: 3″, 2-3/4″, 2-1/2″, 2-1/4″, 2″, 1-3/4″, 1-1/2″, 1-1/4″, and 1″.
2. Take the widest piece and adhere mounting tape across the center.  Take 8″ of ribbon, fold, and place on the mounting tape.
3. Roll.
4. Take the second widest piece and adhere mounting tape across the center.
5. Roll.  Repeat for all pieces, going from widest, until you’ve rolled the second last piece.
6. When you get to the narrowest piece, place the mounting tape directly on the center of the ornament, and cut it about 3/4″ from where you began.  Place double sided tape where the seams will meet.  This will ensure the final seam is flat, and not raised.
7. Roll the final piece only once around and cut at the seam.
8. Take a long strip of construction paper at 1/8″ wide and quill (roll) until you get curls and cut at random lengths.  Dip the quilled strips in glue and apply across the ornament


Read More

DIY OMBRE GLASS ORNAMENTS

12:01:00 0


To make the ornaments, you will need: DecoArt transparent Glass Stain, clear glass ornaments, string, a small round bowl to dip the ornament in, and a paper grocery bag to catch any drips.
Step 1: Clean/dust outside of ornament with a damp cloth.
Step 2: Empty out entire bottle of glass stain into your dish.
Step 3: Tie end of a ~12 inch long string to top of the ornament. Knot a loop on the other end to hang the ornament while the paint dries.
Step 4: Wrap string around your hand and fingers so that it isn’t in the way, and submerge ornament about halfway. Pull out, letting paint drip off, then submerge again about 1/3 of the way. Pull ornament out, then submerge in smaller increments.
Step 5: Hang ornament over a paper grocery bag to drip-dry. I hung my ornaments off my cabinet knobs in the kitchen. The stain will pool to the bottom of the ornament, creating a little bubble. While the paint is wet, gently wipe this off with your fingertip. I left the ornaments to dry, but returned every 10 minutes to wipe off more paint. If the paint hardens, this is a little trickier to do. Just smooth it against the ornament gently.
Step 6: Cover any leftover paint with plastic wrap (use this paint for step 7).
Step 7: When the first layer of stain is completely dried. I dipped just the lower 1/4 my ornament back in to deepen the color. Let dry.



Read More

.

snowman wreath

Crafts mason jar Christmas decor

11:53:00 0

Crafts mason jar Christmas decor - Very cute idea!

Read More

Wednesday, 13 November 2013

Christmas Wreath

Pretty Drawstring Pouch {Tutorial}

05:58:00 0
Pretty Drawstring Pouch,Drawstring Pouch,Tutorial

If you are after a little drawstring pouch to hold a few essentials or to use as gift packaging, the Pretty Drawstring Pouch will fit the bill. Made from two fat 1/8's of quilting cotton and a length of ribbon, it can be made in under an hour. The lining is folded over to the front to make a contrasting casing for the drawstring.
It is sized at 6 1/2 x 6 1/2 inches (16.5 cm x 16.5 cm).


Materials:
  • 2 fat 1/8's quilting cotton - floral and polka dot
  • 42 inches (107 cm narrow ribbon (1/4 inch wide)
Note: Seam allowance of 1/4 inch included.

1. Using the template, cut out two outer pieces (floral), and two lining pieces (polka dot). 
2. Place the two outer pieces (floral) with the right sides facing. Stitch around from one side to the other, leaving the top open. Clip corners. Press.
3. Place the outer pouch on top of the lining panel (polka dot) and make a mark with a water soluble pen, just above the stitching line on both sides (as marked in Photo 3). Pin the two lining pieces together with the right sides facing. Stitch from the mark on one side around to the mark on the other side.  Clip corners. Press.
4. Clip the seam of the lining at a 45 degree angle as shown in Photo 4. Repeat for each side. Press the seam allowance open. This will form part of the casing.

5. Stitch around the seam allowance on both sides of the casing as shown in Photo 5. 6. Turn the floral part of the pouch so that the print is facing outwards. Place the lining inside the pouch. There will be 3/4 inch (2 cm) of the lining showing at the top and this will form the casing. Press this part of the lining down so that it is level with the top of the pouch. Fold under 1/4 inch along the edge of the casing. 7. Pin the casing in place. 8. Stitch along the top and bottom edge of the casing. Cut the ribbon in half lengthwise. Using a safety pin, thread the ribbon through the casing on one side, and right around to exit on the same side. Repeat with the other piece of ribbon from the other opening. Knot the ends of the ribbon. Press.

Pretty Drawstring Pouch,Drawstring Pouch,Tutorial

And there you have it - a quick little pouch to hold all manner of things. 

Pretty Drawstring Pouch,Drawstring Pouch,Tutorial


Read More

24 BEAUTIFUL GIFT WRAPPING IDEAS